-
National framework for electricity safety proposed
The Energy Networks Association (ENA) recently released the ‘Proposed National Framework for Electricity Network Safety’ document as the recommended approach to national electricity network safety regulation.
-
Testing and tagging revisited
Testing and tagging is one element of electrical safety that has caused confusion since its inception. In NSW, an amendment was recently issued to clarify which appliances and environments need to be part of an ongoing testing and tagging routine
-
Project engraving, lasers and digital print and die-cutting equipment
The Project range of engraving, lasers and digital print and die-cutting equipment gives users in-house signage capabilities and includes the entry-level Roland EGX30 engraver through to Epilog lasers systems.
-
The Simpsons workplace safety posters
The Simpsons workplace safety posters, featuring characters from the TV series, are designed to reduce workplace injuries. The characters illustrate ways to work safely using their unique brand of humour.
-
NHP Emergency Lighting Test Unit
The Emergency Lighting Test Unit has been redesigned to make testing emergency and exit lighting more time-efficient. Building codes require that emergency and exit lighting be inspected and tested every six months.
-
Legrand Lipso decorative lighting
The Lipso range of decorative lighting has the advantage of being able to provide clear direction in power outage situations.
-
Low-profile LED light bars
Optimax LED light bars are low-profile emergency light bars that are available in 12 and 24 V versions and in a number of widths including 0.8, 1.2 or 1.4 m.
-
Portable emergency lighting
Montville Creative Products has released a range of rechargeable emergency torches and lanterns that switch on automatically during a power failure.
-
Insulated safety mats
Extreme Safety has a range of insulating mats for almost any use. All mats comply with relevant standards and are supplied tested and ready to use.
-
Universal power alert
The UPA-130 universal power alert is designed to reduce the risk of electrical arc flash by pre-verifying the electrical isolation from the outside of a control panel. The device is hard wired to the circuit breaker or main disconnect and flashes whenever voltage is present. It is engineered with redundant circuitry, which allows it to be powered by the same voltage that it indicates.
-
Safety sign holders
Eye-Catcher sign holders and accessories are a practical solution for indoor and outdoor safety signs, with a broad range of standard safety signs that can be downloaded free, printed and then placed in the sign holders.
-
OHS compliance course
The OHS compliance course is designed for individuals with OHS responsibilities in more than one jurisdiction, guiding them through the similarities and differences across state and territory borders.
-
Contractor safety course
The contractor safety management course is designed for business owners, construction safety project managers, human resource managers and purchasing managers involved in the selection and management of contractors in the workplace.
-
Nonmetallic contact voltage meter
The Hioki Safety HiTester 3258 provides electricians with a safe and convenient means to measure voltages in circuit breaker compartments and other control cabinets.
-
Safety products catalogue
The latest edition of Seton Australia’s catalogue and source book has just been launched. Seton’s range of products and services helps companies comply with new safety regulations and keep work environments as safe and productive as possible.
-
Switchboard inspection window
The Hawk IR Sightglass is a 75 mm diameter inspection window fitted to the door or inspection cover of electrical equipment enclosures. For the safe visual and thermal inspection of internal electrical components without the need to open any enclosure.
-
Earth leakage clamp
The T2007B earth leakage clamp meter has been designed to meet the IEC1010-1 and IEC1010-2-0.2 standard.
-
Low-voltage switchboards
Signature SE is a range of low-voltage switchboards for motor control centres in the mining sector, with a flexible modular design incorporating a wide range of compartment options.
-
Lockout stations
The LST series lockout stations are for wall mounting in workshops, plants, commercial buildings and factories to keep and control lockout devices, safety tags and lockout padlocks in one place.
-
Audible evacuation sign
The Zoneworks Sound Escape system is designed to provide an enhanced solution for evacuation from buildings combining both visual and sound cues.
-
GenSafe electrically safer generators
Concerned about electrical safety when your workforce uses generators? Not sure if the earth stake gets correctly connected so that the safety switch will work?
-
Efficient emergency lighting
The Slide Connect G2 is designed to use up to 70% less energy than a conventional fluorescent emergency and exit lighting system. Designed and manufactured in Australia, the lighting fixture uses a single high brightness LED, which is 'under run' in normal conditions to conserve energy and extend lamp life, but operates at full brightness in emergency situations.
-
Customisable battery charges
Amtex Electronics has developed a customisable battery charger that maintains voltage levels in emergency service and rapid response vehicles to ensure there is no failure in starting a vehicle or powering its communications equipment. The technology is suitable for any type of vehicle, including ambulances, mine and refinery emergency vehicles, SES trucks, SWAT team vans, metropolitan fire tankers, workplace emergency units, country fire and rescue vehicles, rural emergency services and federal security vehicles.
-
Low-cost PAT with free reporting software
The TRIO-LCB portable appliance tester is now supplied with free Inspect reporting software. This combination offers a low-cost solution for compliance to AS/NZ3760.
-
Protex leads electrical safety for generators
Recent headlines have highlighted electric shocks as a persistent risk.
-
Protex leads electrical safety for generators
Recent headlines highlighted electric shocks as a persistent risk.
-
Switchboard inspection window
The Hawk IR Sightglass is a 75 mm diameter inspection window fitted to the door or inspection cover of electrical equipment enclosures. For the safe visual and thermal inspection of internal electrical components without the need to open any enclosure.
-
Electrical safety testers
Extech has released two products designed to simplify data processing of electrical safety testing measurements. The Extech Opt.758 ethernet card and Opt.751 multifunction USB card both slot into the Extech 7742 safety tester which provides dielectric strength, insulation resistance, earth continuity and leakage testing, thus facilitating data exchange and control of testing protocols.
-
Safety lamps
Cov-R-Guard Lamps are wrapped in a casing of Lexan plastic that effectively contains glass fragments and phosphor if the lamp is broken. The casing allows for maximum protection, with minimum light loss - keeping an installation bright and safe. Both the casing and the lamp are fully recyclable, once separated.
-
Portable/personal lights
Where low light conditions, traffic flow difficulties and emergencies require quick and effective management, Vision Safe's range of Signal Lites is an option.
-
Lighting range
Thorn's Jet fitting has been designed for contractors and installers who are dissatisfied with over-complicated, poor quality street lighting fittings. Jet provides an aesthetic, vandal-resistant, easy-to-use IP65 compact street lighting fitting, suitable for use in a wide variety of road applications.
© 2010 Westwick-Farrow Pty Ltd. All Rights Reserved. Designated trademarks and brands are the property of their respective owners. Use of this website constitutes acceptance of our
Terms and Conditions
and
Privacy Policy.